Download Process Piping Design Handbook, Volume 3 - Planning Guide to Piping Design PDF

TitleProcess Piping Design Handbook, Volume 3 - Planning Guide to Piping Design
File Size9.9 MB
Total Pages212
Table of Contents
                            Front Matter
List of Figures
List of Tables
Preface
Table of Contents
1. Before You Begin
	1.1 Introduction
	1.2 Standards
		1.2.1 Standard Drawings
		1.2.2 Charts
		1.2.3 Drawing Templates and Drawing Standards
		1.2.4 Drawing Numbering
		1.2.5 3-D Model Numbering
		1.2.6 Material Commodity Codes
	1.3 Specifications
		1.3.1 Piping Classes
	1.4 Procedures
		1.4.1 Stick Files
		1.4.2 Inter-Discipline Drawing Reviews
		1.4.3 Line Numbering
		1.4.4 Stress Analysis
		1.4.5 CAD Set-up
		1.4.6 3-D Model Reviews
		1.4.7 Checking
		1.4.8 Manhour Estimating
		1.4.9 Progress Reporting
		1.4.10 Management of Change
		1.4.11 As-Builting
		1.4.12 Project Close-out
	1.5 Piping Execution Plan
		1.5.1 Design Basis Memorandum DBM
		1.5.2 Project Execution Plan PEP
		1.5.3 Contracting and Procurement Plan and Construction Execution Plan
	1.6 Conclusion
2. Procedures
	2.1 Introduction
	2.2 Master Stick Files, Working Copies, and Inter-Discipline Drawing Reviews IDR
		2.2.1 Master Stick Files
			2.2.1.1 Storing Master Stick Files
			2.2.1.2 Managing Master Stick Files
		2.2.2 Working Copies
			2.2.2.1 Managing Working Copies
		2.2.3 Inter-Discipline Drawing Reviews
			2.2.3.1 Managing Inter-Discipline Drawing Reviews
	2.3 Vendor Drawing Reviews
	2.4 Line Numbering
		2.4.1 Line Numbering Rules
	2.5 Stress Analysis
		2.5.1 The Stress Analysis Procedure
		2.5.2 Stress Analysis Procedure Notes
			2.5.2.1 Set-up
			2.5.2.2 Monitoring Progress
3. Deliverables
	3.1 Introduction
	3.2 Deliverables
		3.2.1 Cover Sheets and Drawing Indexes
			3.2.1.1 A Cover Sheet Identifies
			3.2.1.2 Drawing Indexes List
		3.2.2 Plot Plan
		3.2.3 Key Plans
			3.2.3.1 Piping Arrangement Key Plan
			3.2.3.2 Model Key Plan
			3.2.3.3 Module Key Plan
			3.2.3.4 Construction Work Package Key Plan
		3.2.4 Location Plans
			3.2.4.1 Equipment Location Plans
			3.2.4.2 Tie-In Location Plan
			3.2.4.3 Utility Station Location Plan
			3.2.4.4 Safety Shower and Eye Wash Location Plan
			3.2.4.5 Heat Tracing Manifold Location Plan
		3.2.5 Piping Arrangements
		3.2.6 Isometrics
		3.2.7 Isometric Logs
		3.2.8 Tie-In Isometrics
		3.2.9 Tie-In List
		3.2.10 Demolition Drawings
		3.2.11 Heat Tracing Circuit Layouts
		3.2.12 Heat Tracing Logs
		3.2.13 3-D Models
		3.2.14 Model Indexes
		3.2.15 CWP Drawing Packages and Scopes of Work SOW
			3.2.15.1 CWP Drawing Packages
				3.2.15.1.1 Project Drawings
				3.2.15.1.2 Construction Drawings
				3.2.15.1.3 Standard Drawings
				3.2.15.1.4 Vendor Drawings
			3.2.15.2 Scopes of Work SOW
		3.2.16 Process Flow Diagrams PFDs
		3.2.17 Piping and Instrumentation Diagrams P&IDs
		3.2.18 Line Designation Tables LDTs
4. Detailed Design
	4.1 Introduction
	4.2 Contracting and Procurement Plan and Construction Execution Plan
	4.3 Modularized and Field Erected Piping Splits and CWP Boundaries
		4.3.1 Notes to Figure 4-1
	4.4 Model Boundaries
		4.4.1 Study Model Boundaries
			4.4.1.1 Notes
		4.4.2 Detailed Model Boundaries
			4.4.2.1 Notes
	4.5 Shop and Field Material Splits
	4.6 Procurement Splits
	4.7 Issued for Bid and Bid Evaluations
		4.7.1 Issued for Bid
		4.7.2 Clarifications from Bidders and Bid Evaluations
	4.8 Equipment Coordinates and Elevations
	4.9 Module Design
		4.9.1 Design Considerations
	4.10 Module Numbering
	4.11 Drafting Practice
		4.11.1 A Brief History
		4.11.2 3-D CAD Drafting Practice
		4.11.3 Ownership and Training
		4.11.4 Piping Arrangements
		4.11.5 Isometrics
	4.12 Holds
	4.13 Project Binders and Lists
		4.13.1 Project Binders
		4.13.2 Piping Job Notes and CAD Job Notes
		4.13.3 Action Item List and Needs List
		4.13.4 Equipment List
		4.13.5 Data Sheets
	4.14 Managing Standard Drawings
	4.15 Project Meetings
	4.16 Progress Monitoring
	4.17 Design Change Notice DCN
	4.18 Field Change Notice FCN
	4.19 Request for Information RFI
5. Shop Fabrication
	5.1 Introduction
	5.2 Kick-off Meetings
	5.3 Scopes of Work SOW
		5.3.1 Example of Pipe Spool Fabrication Scope of Work
		5.3.2 Example of Module Fabrication and Assembly Scope of Work
	5.4 Instruction to the Fabricator
		5.4.1 Example of Instruction to Fabricator
	5.5 Requests for Information RFI
	5.6 Visits with the Fabricators
		5.6.1 The Value of Shop Visits
		5.6.2 Supporting the Fabricators
	5.7 Automatic Spool Generation
	5.8 Conclusion
6. Field Construction
	6.1 Introduction
	6.2 Support from the Home Office
		6.2.1 Kick-off Meetings
		6.2.2 Field Erection of Piping Scope of Work
			6.2.2.1 Example of Field Erection of Piping Scope of Work
		6.2.3 Computers, 3-D Software Set-ups, and Maintenance
		6.2.4 Request for Information
	6.3 Support in the Field
		6.3.1 Utilizing the 3-D Models
			6.3.1.1 Generating Reports
			6.3.1.2 Generating Screen Shots
			6.3.1.3 Construction Planning
		6.3.2 Problem Solving
		6.3.3 Punch Lists and Deficiency Reports
		6.3.4 Compiling and Submitting RFIs
		6.3.5 Investigating Back Charges and Extras
		6.3.6 Progress Monitoring
		6.3.7 Maintaining the Master Stick Files
		6.3.8 As-Builting
	6.4 Lessons Learned
	6.5 Safety
Appendix A: Abbreviations
A
B
C
D
E
F
H
I
K
L
M
N
O
P
R
S
T
V
W
                        

Similer Documents